Ford Focus Drivers Armrest
.25% Ford Customer Saving has been applied to the above online price. This Customer Saving is provided to retail customers only by Ford Motor Company Limited (registered office Arterial Road, Laindon, Essex, England, SS15 6EE). This Ford Customer Saving is available on orders made on the Ford Online Shop. In addition, this Ford Customer Saving may be available at participating dealers (you will need to speak to your dealer for full information).This website shows both original Ford accessories as well as a range of carefully selected products from third party suppliers, which are identified under that third party supplier’s brand name. Please note that third party supplier branded accessories do not come with a Ford warranty but are covered by the third party supplier’s own warranty, the details of which can be found.Fitment of dealer-fit parts and accessories may have an impact on your vehicle’s fuel consumption.
Thu 16 Aug 2002 1.6 Ghia - Driver's Armrest & Lumbar Support - drawdeHiI have a 2002 Ford Focus 1.6 Ghia, and the armrest and lumbar support on the drivers seat do not work. The armrest is stuck in the up position, and will no longer unlock to be lowered. The lumbar support which adjusts with a wheel on the hinge of the armrest) has also stopped working, but not at the same time.
One time while adjusting it, there was a clunk and turning the wheel ceased to have any effect.Is there any chance these are related, and can either be cured easily? Unfortunately, neither is mentioned in the Haynes manual, so I'm completely stumped.
I'm reasonably handy with a spanner, as long as the task is reasonably obvious or I have instructions, but I don't want to be dismantling and reupholstering the whole seat.ThanksdrawdeEdited by Dynamic Dave on at 20:31. Sat 22 Mar 2008 20:47Driver's Armrest & Lumbar Support - drawdeUnfortunately I did not. I got hold of some part breakdown diagrams from Ford, and the armrest has to be removed as a single unit and replaced (£75 + VAT for the parts). I had a go taking it apart myself, figuring that I couldn't do any more damage, but it's really well sealed.As for the lumbar support, there are about 15 different things it could be, all of which require stripping down the seat. So I'm coping with both problems for now. Might look for a replacement seat in the scrapyards, grey velour can't be that rare.
Tue 26 Apr 2011 11:28Driver's Armrest & Lumbar Support - AlanSimmondsApril 2011The following is my experience on my brothers Ford Focus.It's a 2004 model, I can only relate what I saw here.Downward pressure on the arm rest has to be resisted by theteeth on the ratchet. Due to the length of the armrest, forceapplied to the end of the armrest is magnified some ten fold atthe ratchet pawl. Most likely, the driver wants to turn round toget something off the back seat and puts weight with his elbow onthe rest, probably right on the very end.The armrest is stuck up in the half past twelve position.The pawl is solid metal and quite strong, however the ratchet seemsto be of some light cast alloy and is brittle. At the end of theratchet is attached a piece of spring steel, there is not much materialbetween that and the last ratchet tooth, so the alloy fractures if toomuch force is applied to the armrest. The spring steel breaks off also,leaving no means of releasing the pawl, hence the armrest is stuck.To get inside the armrest at the mechanism without removing the armrest:The lumber support wheel should just pull off, according to my brother,though I didn't actually do this. The end of the wheel shaft had split,see later.At the rear of the armrest, slightly underneath, was a black plastic zip.The zip tag was tucked out of sight between the armrest and the seat side.Use a small screwdriver or hook to pull this out and undo the zip.Remove the armrest cover by peeling off from the back and then off the front.Remove the foam rubber again starting from the back.
Mine teared easily, but by tearing sufficient to just get it off the circular end and along the bottom it will slide off the front. Keep any bits as it can all be stuffed back later.I saw three brass screw heads.
Remove three screws, remove the side cover of the armrest. Now I saw the spring steel and snapped off alloy part. I see no way this can be mended ) unless you remake the whole ratchet bit, nor (because the bits are rattling about) am I able to work out how the ratchet works when using the armrest as described in the Ford Owners Manual.There was a large diameter brass coloured spring tab washer used to hold the armrest in place on the metal shaft.
This can be removed but gave me no advantage, so leave alone.I saw the pawl and spring, I can now manually retract the pawl and put thearmrest down. Fortunately there were sufficient teeth left on the ratchet to leave it in a comfortable driving position. Refit the side cover, screws, foam and cover.Try to remember not to move the armrest up.To remove the armrest completely from the seat:Pull off the lumber support wheel.As mentioned previously, dig between the armrest and the back upholstyry to remove the large spring clip. It's made of wire, U shaped with squarish corners. You may be able to see part of the clip when looking down the hole where the lumber support wheel goes. I can, with a little difficulty, twist the white plastic inside the hole to adjust the lumber support. Use pliers to grip the wire clip and pull back.
2005 Ford Focus Armrest Repair
I can now get a largish screwdriver between the armrest and seat (blade held flat) and use it to lever the armrest off it's shaft. It will be quite stiff but once you find the right leverage point the armrest will wiggle off.